TEST METHOD OF CLT BY TENSION PERPENDICULAR TO GRAIN

Authors

DOI:

https://doi.org/10.26906/znp.2018.50.1070

Keywords:

cross laminated timber, tension perpendicular to the grain, proposing of size of test specimens, test arrangement

Abstract

It is known that cross laminated timber (CLT) is a relatively new material in timber design. There is no information about its behavior and strength in tests by tension perpendicular to grain. Little information available is based only on simple tests for assessing the bearing capacity of some variants of devices which are used for the installation of
CLT panels. In practice tension perpendicular of CLT panels occurs in curved CLT panels and in some wall-floor connections with screws. First proposed of test setup is based on the parameters related to solid timber and glulam after detailed analysis. The main influence factors on the tensile strength perpendicular to grain were investigated, and the necessary sizes of the CLT specimens were determined considering the features of the material structure. The recommendations derived in this publication can be included in standard EN 16351 or EN 408.

References

Blass H. J. Tensile strength perpendicular to grain according to EN 1193 / H. J. Blass, M. Schmid // Proc. of the Intern. council for research and innovation in building and construction, Working commission W18 – timber structures, Meeting 31. – Savonlinna, Finland, 1998. – 143-158p., CIB-W18/31-6-2.

Blass H. J. Tensile strength perpendicular to grain of glued laminated timber / H. J. Blass, M. Schmid // Proc. of the Intern. council for research and innovation in building and construction, Working commission W18 – timber structures, Meeting 32. – Graz, Austria, 1999. – 157-169p., CIB-W18/32-6-4.

Aicher S. Evaluation of Different Size Effect Models for Tension Perpendicular to Grain Design / S. Aicher, G. Dill-Langer // Proc. of the Intern. council for research and innovation in building and construction, Working commission W18 – timber structures, Meeting 35. – Kyoto, Japan, 2002. – 73-84 p., CIB-W18/35-6-1.

Ranta-Maunus A. Duration of Load Effect in Tension Perpendicular to Grain in Curved Glulam / A. Ranta-Maunus // Proc. of the Intern. council for research and innovation in building and construction, Working commission W18 – timber structures, Meeting 31. – Savonlinna, Finland, 1998. – 293-305 p.,CIB-W18/31-9-1.

Statement VTT-S-05156-11, Special lay-ups of Kerto (later on renamed to Kerto-Qp) – Characteristic values // VTT Expert services ltd. – Finland, 2010. – 4 p.

Certificate № 184/03, Kerto-S and Kerto-Q Structural laminated veneer lumber // VTT Expert services ltd. – Finland, 2004. – 40 p.

Allgemeine bauaufsichtliche Zulassung Z-9.1-811. Furnierschichtholz «Ultralam R», «Ultralam RS» und «Ultralam X» // DIBT. – 2015. – 11 p.

Prufbericht 51220-901.6453.000/2, Bestimmung mechanischer und physikalischer Eigenschaften des Furnierschichtholzes ULTRALAM R bestehend aus Furnieren der Holzart Fichte // MPA Stuttgart, 2009. – 46 p.

СТО 36554501-021-2010. Деревянные конструкции. Многослойный клееный из шпона материал Ultralam (ультралам). Общие технические требования // ЦНИИСК. – М., 2010. – 19 c.

STO 36554501-021-2010. Derevyannie konstrukcii. Mnogosloinyi kleeniy iz shpona material Ultralam (Ultralam). Obshie tehnicheskie trebovaniya // TSNIISK. – M., 2010. – 19 s.

EN 384. Structural timber – Determination of characteristic values of mechanical properties and density // European Committee for Standardization (CEN). – Bruxelles, Belgium, 1995. – 16 p.

EN 14080. Timber structures – Glued laminated timber and glued solid timber – Requirements // European Committee for Standardization (CEN). – Bruxelles, Belgium, 2013. – 110 p..

EN 408. Timber structures – Structural timber and glued laminated timber – Determination of some physical and mechanical properties // European Committee for Standardization (CEN). – Bruxelles, Belgium, 2010. – 42 p.

EN 16351. Timber structures – Cross laminated timber – Requirements // European Committee for Standardization (CEN). – Bruxelles, Belgium, 2015. – 106 p.

Downloads

Published

2018-04-11

How to Cite

Bidakov, A. M., & Raspopov, I. A. (2018). TEST METHOD OF CLT BY TENSION PERPENDICULAR TO GRAIN. Academic Journal Industrial Machine Building Civil Engineering, 1(50), 148–159. https://doi.org/10.26906/znp.2018.50.1070

Similar Articles

1 2 3 4 5 6 > >> 

You may also start an advanced similarity search for this article.